Treler tander kayu

Fliegl TPS 118 Plateau 6,2m für Holz

Customized transport solution
Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements.

Fine-grained steel welded construction
Outer frame slightly inclined with "Load-Lock profile" for attaching lashing straps
Gearbox support at the front
Foldable rear support
2 chock blocks with holder
Under-ride guard, steel, galvanized
Splash flaps at the rear, covering the entire width
Quarter panel fenders according to EC standards
with anti-spray splash flaps according to EC standards
1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable
Storage compartment for lashing equipment, open, under the loading area
4 lashing/spar bars recessed in the floor, running transversely across the entire width to the outer frame (max. usable inner width between the outer spar bars approx. 2170 mm), approx. 100 mm high. With 20 mm round steel bars, top and bottom, spacing from top to bottom approx. 60 mm (of the round steel). Bottom with an angle plate as a closure, open halfway downwards. For lashing and inserting spar bars 80 x 80 mm.
4 pairs of spar pockets recessed in the outer frame, internal dimensions 83 x 83 mm
4 spar pockets recessed in the center of the floor, with reinforcements to the main frame, internal dimensions 83 x 83 mm
6 pairs of spar bars, W=80/ D=80/ L=2000 mm, hot-dip galvanized
Note: Spar pockets/insertions are not designed for the sole securing of long materials, pipes, etc. without wrapping around.
Side impact protection, aluminum
Coupling device, tandem trailer
Drawbar with tested 40 mm towing eye
Drawbar mechanically adjustable in length by 4 x 500 mm, from 1800 - 3800 mm, drawbar length set to 1800 mm
Axles + Suspension
Axles according to manufacturer's choice, with tapered roller bearings and S-cam brake
"Axle/chassis laser measured" reduces tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (rocker arm compensation)
Wheels and tires
235 / 75 R 17.5" according to manufacturer's choice
Hnedpfx Aei Ri H Dol Nen
Steel rims, factory silver
Braking system
2-line compressed air braking system
Spring brake parking brake
Integral air reservoir
2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle,
ABS and ALB, with ABS connector at the front, with connecting cable
Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS!
Electrical system
24 Volt, multi-chamber lights in LED, yellow LED lighting on the sides, license plate lighting in LED, (Note! with certain towing vehicles, false diagnoses may occur, although the function is given)
2 white position lights at the front in LED
2 white/red side marker lights at the rear in LED
2 x 7-pole fail-safe plugs at the front, with connecting cable
Floor
Plywood panels, approx. 30 mm thick, for high point load capacity
Note: Floor deflection due to weather influences is possible!
Platform length approx. 6,200 mm
Operating instructions
Special permit required if the overall length of the combination exceeds 18,750 mm. Observe country-specific registration regulations.
Approval / Signs
Country of registration: Germany
with Dekra inspection and certificate
Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear
Paintwork
Frame hot-dip galvanized including passivation
"15-year warranty against rust perforation

Iklan ini diterjemahkan secara automatik. Mungkin terdapat kesilapan terjemahan.