Pemuat rendah

Fliegl DTS S 300 Parab/Feder

Further information
Chassis low loader trailer
Welded steel construction
Turntable with powerful ball bearing slewing ring
Folding rear support
2 wheel chocks with holder
Aluminum side bumpers
Rear spray flaps across the entire width
Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle
1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery)
Extensions extendable to 3,000 mm
Storage compartment for wooden planks in the middle of the loading area
Wooden planks 70 mm for widening to 3000 mm
Low loader lashing eyes (40 lashing options)
1 pair of lashing cut-outs in the front side member on offset, 10 tons each
4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment)
7 pairs of lashing points at the top and sides of the outer frame, 10 tons each
1 x front on offset
6 x in the drop deck
First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm
5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery)
2 additional pairs of hinged lashing eyes, 10 tons each
1 x on offset (protrudes)
1 x embedded in the floor behind the last axle
Trailer drawbar Turntable
Drawbar with tested 40 mm drawbar eye
Axles + suspension
Drum brake axles, at the manufacturer's choice
Axle/chassis laser-measured Reduction of tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation)
Wheels and tires
235 / 75 R 17,5
at the manufacturer's discretion
Twin steel rims, factory silver
Brake system
2-line compressed air brake system
Spring-applied parking brake
2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle,
ABS and ALB, with ABS plug at the front, with connecting cable
Make: Wabco or Knorr
Electrical system
24 volt, multi-chamber lights, amber LED lighting at the side
2 white position lights at the front
2 white/red rear lane departure lights
2 x 7-pin interchangeable plugs at the front, with connecting cable,
1 LED rotating beacon with holder, switched via parking light (removable light)
2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm
Floor
Front offset with steel/ checker plate covering
Storage box recessed into the drive-over slope to the offset
Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area
Rear slope with 70 mm softwood floor
Deep loading area incl. rear slope 6,500 mm
Drive-on ramps
Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways
covered with wood
with spring lift support
Country of registration / plates
Country of registration: Germany
24/7 service hotline
Nedpfx Agei Ri Ddsgswp
Prepared for two-line license plate holder
Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear
Warning sign according to ECE - 70
Paintwork
Hot-dip galvanized frame incl. passivation
15-year warranty against rusting through
Drawbar Galvanized or black, at the manufacturer's discretion
Drive-on ramps Hot-dip galvanized
Attention! These are archive pictures!

Iklan ini diterjemahkan secara automatik. Mungkin terdapat kesilapan terjemahan.